An air suspension cushion to reduce human exposure to vibration

SUNScholar Research Repository

Show simple item record

dc.contributor.advisor Van Niekerk, J. L.
dc.contributor.author Van der Merwe, Andre Francois
dc.contributor.other University of Stellenbosch. Faculty of Engineering. Dept. of Industrial Engineering.
dc.date.accessioned 2008-01-17T12:23:03Z en_ZA
dc.date.accessioned 2010-06-01T08:15:06Z
dc.date.available 2008-01-17T12:23:03Z en_ZA
dc.date.available 2010-06-01T08:15:06Z
dc.date.issued 2007-03
dc.identifier.uri http://hdl.handle.net/10019.1/1209
dc.description Thesis (PhD (Industrial Engineering))--University of Stellenbosch, 2007.
dc.description.abstract Off-road working vehicles are subjected to high levels of vibration input on the rough terrain and irregular roads they work. The human operators are therefore exposed to high levels of whole body vibration (WBV) and at risk of developing health problems. A number of international standards address the matter of whole body vibration, and the European Union issued a directive which limits the exposure of workers in the EU to WBV. Unfortunately, to date there is no law in South Africa requiring compliance with any of these EU standards nor guidelines. There are vehicles which are not fitted with suspension and/or suspension seats. The three wheeled logger used in forestry is a highly manoeuvrable and effective bulk handler, but without any form of suspension and no space under the operator’s seat to install a suspension seat. However, a suspension cushion can be retrofitted to existing vehicles largely alleviating the problem. To isolate low frequency vibration large suspension travel is required which makes an air suspension cushion attractive, as it can fully collapse. Additionally, a Helmholtz resonator if added to the cushion in the form of a pipe and tank, provides anti-resonance at a specific frequency. The resonator can be tuned by adjusting the pipe’s length and diameter as well as the volume of the tank. Larger diameter pipes have less friction and give better reduction of the transmissibility curve at the anti-resonance frequency. The SEAT value is a single number used to compare suspension seats for a specific input vibration. It is calculated from the weighted input acceleration power spectral density curve and the suspension seat transmissibility curve. The former is obtained from the vehicle and is vehicle, path and speed dependent. The latter is the only variable that can be improved by using a better suspension seat/cushion. The input power spectral density often contains significant energy at frequencies where the human operator is most sensitive. The cushion resonator could be tuned to position the anti-resonance in the transmissibility curve at these frequencies. The resultant output vibration would thus be lower than the input vibration at that frequency. In this dissertation an analytical model describes the state variables in the cushion, pipe and tank. A Simulink model predicts the transmissibility curve with a solid mass as well as with a two degree of freedom seated human model. Initially the prototype was tested with a solid mass to compare the transmissibility curve produced by the simulation with the experimental results. It was required to evaluate the contribution of the resonator without the complexity of the human impedance. Subsequent tests were carried out with human subjects. Test results showed high inter subject similarity at the anti-resonance frequencies. Design guidelines are formulated that can be used by the suspension cushion designer to specify the pipe diameter and length and the volume of the tank to determine the optimal transmissibility. Input psd from ISO7096 class EM3 vehicles is used as an example during the design process. A prototype air suspension cushion was designed to reduce output vibration on the three wheeled logger. Laboratory tests with human subjects showed a significant improvement at the problematic frequencies through the tuning of the resonator. Using a Helmholtz resonator with the air suspension cushion the overall SEAT value improved by 25% compared with a 100mm foam cushion. However, the current tank and pipe need to be reduced in size for practical implementation to the vehicle. Future work would include finding an alternative mass to replace the air in the pipe. This should reduce the size of the tank and the pipe required. Additionally the simultaneous effect of multiple resonators at different frequencies should be investigated. This is required for vehicles having an input psd with significant energy at more than one frequency band. en
dc.format.extent 3832205 bytes en_ZA
dc.format.mimetype application/pdf en_ZA
dc.language.iso en
dc.publisher Stellenbosch : University of Stellenbosch
dc.subject Dissertations -- Industrial engineering en
dc.subject Theses -- Industrial engineering en
dc.subject Vibration en
dc.subject Shock (Mechanics) en
dc.subject Human engineering en
dc.subject Active noise and vibration control en
dc.title An air suspension cushion to reduce human exposure to vibration en
dc.type Thesis
dc.rights.holder University of Stellenbosch


Files in this item

This item appears in the following Collection(s)

Show simple item record

-->